Locating and Clamping Shank Dimensions Each Kit Includes: • Replacement Screw • Locking Balls • Drive Ball • O-Ring Ball Lock® Repair Kits Any Ball Lock® application requires at least two sets of shanks, receiver bushings and liners. The liners are placed into the xture plate to insure extremely accurate positioning. If more than two shanks are required (to provide additional hold down force), omit the liner bushing so that these additional holes will not interfere with your primary locating holes. • Material: Shank/Bushing, 4340 Liner, 52100 • Finish: Black Oxide • Heat Treat: Shanks, RC 40-45 Bushings, RC 50-54 Liners, RC 62-64 • Operating Temperature Range -20° to 400°F, -30° to 200°C Locating and Clamping Shanks See page 23 for Fast Acting Shanks. Stainless Steel available. See Page 20-21 Shank Diameter (mm) A Fixture Plate Thickness ±0.005 Shank Part Number Head of Shank Length Under Head D Hex Wrench Size for Set Screw Maximum Recommended Shank Repair Kit Part Number Height B Diameter C Screw Torque (Ft/lb) Hold-Down Force (lbs) Screw Torque (Ft/lb) Hold-Down Force (lbs) 13 0.50 49605 0.25 0.87 1.08 3/32 1.2 750 1 625 49905 — 0.75 49606 — — 1.33 — — — — — 49906 — 1.25 49604 — — 1.83 — — — — — 49904 16 0.50 49607 0.32 1.50 1.15 1/8 3 1200 2 800 49907 — 0.75 49608 — — 1.4 — — — — — 49908 — 1.25 49609 — — 1.90 — — — — — 49909 20 0.75 49601 0.38 1.75 1.53 1/8 4 3000 3 2250 49901 — 1.00 49602 — — 1.78 — — — — — 49902 — 1.50 49603 — — 2.28 — — — — — 49903 25 0.75 49611 0.38 2.00 1.70 5/32 9 7000 7 5444 49911 — 1.00 49612 — — 1.95 — — — — — 49912 — 1.50 49613 — — 2.45 — — — — — 49913 30 0.75 49621 0.50 2.25 1.88 3/16 15 10000 12 8000 49921 — 1.00 49622 — — 2.13 — — — — — 49922 35 0.75 49631 0.50 2.25 1.97 1/4 25 15500 19 11780 49931 — 1.00 49632 — — 2.22 — — — — — 49932 — 1.50 49633 — — 2.72 — — — — — 49933 — 2.00 49634 — — 3.22 — — — — — 49934 50 0.75 49641 0.75 3.00 2.45 3/8 50 20000 38 15200 49941 — 1.00 49642 — — 2.70 — — — — — 49942 — 1.50 49643 — — 3.20 — — — — — 49943 — 2.00 49644 — — 3.70 — — — — — 49944 QUICK CHANGE FIXTURING - ZERO POINT MOUNTING SYSTEM Jergens, Inc. | 15700 S. Waterloo Road | Cleveland, Ohio 44110-3898 USA W18-P1 BALL LOCK® MOUNTING SYSTEM workholding solutions QUICK CHANGE FIXTURING - BALL LOCK® MOUNTING SYSTEM 18 INCH BALL LOCK® COMPONENTS
RkJQdWJsaXNoZXIy NzI2NjY=