Max. Corner Radius 0.5mm Max. Corner Radius 0.5mm H – Tap 3 Holes Equally Spaced On Bolt Circle Dia. METRIC Back Mount Face Mount Installation Dimensions 1 Cap Screws Supplied with Face Mount Bushings. Two styles of receiver bushings are available. Installed bushings should be approximately 0.3mm below subplate surface. Receiver Bushings Face Mount Bushing Installation Instructions Back Mount Bushing Installation Instructions Note on Installation of Press Fit Liners & Back Mount Style Receiver Bushings: To alleviate the possibility of binding the shank in the bore, the maximum interference t between bore and bushing O.D. should not exceed 0.013 mm. Liner Bushings for Fixture Plates Locating repeatability will determine if one primary and one secondary or two primary liners are needed. With two primary liners, repeatability of ±0.013 mm can be maintained if the two holes for receiver bushings are held to a centerline distance of ±0.005 mm tolerance. Generally, the face mount receiver bushing is utilized in blind hole applications (Slip Fit). The back mount receiver bushing is used in through hole applications (Light Press Fit). Shank Diameter (mm) Fixture Plate Thickness +0.13 -0.13 Primary Liner Secondary Liner Liner O.D. +0.00 - 0.01 Part Number I.D. Part Number I.D. 13 13 49755 13.01 49855 13.04 19.040 — 20 49756 — 49856 — 19.040 16 20 49757 16.01 49857 16.04 25.042 — 25 49758 — 49858 — 25.042 20 20 49751 20.01 49851 20.04 35.042 — 25 49752 — 49852 — 35.042 25 20 49761 25.01 49861 25.04 35.042 — 25 49762 — 49862 — 35.042 30 20 49771 30.01 49871 30.04 45.042 — 25 49772 — 49872 45.042 35 20 49781 35.01 49881 35.04 45.042 — 25 49782 — 49882 — 45.042 — 40 49783 — 49883 — 45.042 — 50 49784 — 49884 — 45.042 50 20 49791 50.01 49891 50.04 63.546 — 25 49792 — 49892 — 63.546 — 40 49793 — 49893 — 63.546 — 50 49794 — 49894 — 63.546 Face Mount Back Mount Shank Dia. (mm) Face Mount Part Number Actual O.D. -0.01 -0.02 Clearance Drill Diameter E Bore +0.010 +0.003 F Depth +0.025 -0.025 G Tap Size & Depth1 H Bolt Circle Diameter 3 PL Equally Spaced Min. Subplate Thickness D Shank Dia. (mm) Back Mount Part Number Actual O.D. +0.04 +0.03 A Depth +0.025 -0.025 B C-Bore ±0.15 C Min. Subplate Thickness D 13 49556 35 13.5 35 11.91 M4x0.7 x 7 25 20 13 49566 20 6.92 26 20 16 49557 37 21.0 37 11.91 M4x0.7 x 7 29 20 16 49567 22 7.24 29 20 20 49551 45 21.0 45 16.21 M5x0.8 x 9 35 25 20 49561 28 8.74 33 25 25 49552 55 25.5 55 20.32 M6x1.0 x 10 42 30 25 49562 35 10.54 41 25 30 49553 60 30.5 60 22.15 M6x1.0 x 11 48 35 30 49563 42 10.95 49 30 35 49554 70 40.0 70 22.99 M8x1.25 x 17 56 40 35 49564 48 12.50 55 35 50 49555 92 55.0 92 31.50 M10x1.5 x 18 75 50 50 49565 67 15.75 76 45 QUICK CHANGE FIXTURING - ZERO POINT MOUNTING SYSTEM W38-P1 BALL LOCK® MOUNTING SYSTEM workholding solutions QUICK CHANGE FIXTURING - BALL LOCK® MOUNTING SYSTEM 38 METRIC DIMENSIONS - METRIC BALL LOCK® COMPONENTS Jergens, Inc. | 15700 S. Waterloo Road | Cleveland, Ohio 44110-3898 USA
RkJQdWJsaXNoZXIy NzI2NjY=