METRIC Max. Corner Radius 0.5mm Max. Corner Radius 0.5mm H – Tap 3 Holes Equally Spaced On Bolt Circle Dia. Back Mount Face Mount 1Cap Screws Supplied with Face Mount Bushings. Two styles of receiver bushings are available. Installed bushings should be approximately 0.3mm below subplate surface. Stainless Steel Receiver Bushings Face Mount Bushing Installation Instructions Back Mount Bushing Installation Instructions Note on Installation of Press Fit Liners & Back Mount Style Receiver Bushings: To alleviate the possibility of binding the shank in the bore, the maximum interference t between bore and bushing O.D. should not exceed 0.013 mm. Stainless Steel Liner Bushings for Fixture Plates Liner Dimensions Locating repeatability will determine if one primary and one secondary or two primary liners are needed. With two primary liners, repeatability of ±0.013 mm can be maintained if the two holes for receiver bushings are held to a centerline distance of ±0.005 mm tolerance. Generally, the face mount receiver bushing is utilized in blind hole applications (Slip Fit). The back mount receiver bushing is used in through hole applications (Light Press Fit). Shank Diameter (mm) Fixture Plate Thickness +0.13 -0.13 Primary Liner Secondary Liner Liner O.D. +0.00 - 0.01 Part Number I.D. Part Number I.D. 13 13 49755SS 13.01 49855SS 13.04 19.040 — 20 49756SS — 49856SS — 19.040 16 20 49757SS 16.01 49857SS 16.04 25.042 — 25 49758SS — 49858SS — 25.042 20 20 49751SS 20.01 49851SS 20.04 35.042 — 25 49752SS — 49852SS — 35.042 25 20 49761SS 25.01 49861SS 25.04 35.042 — 25 49762SS — 49862SS — 35.042 30 20 49771SS 30.01 49871SS 30.04 45.042 — 25 49772SS — 49872SS 45.042 35 20 49781SS 35.01 49881SS 35.04 45.042 — 25 49782SS — 49882SS — 45.042 — 40 49783SS — 49883SS — 45.042 — 50 49784SS — 49884SS — 45.042 50 20 49791SS 50.01 49891SS 50.04 63.546 — 25 49792SS — 49892SS — 63.546 — 40 49793SS — 49893SS — 63.546 — 50 49794SS — 49894SS — 63.546 Installation Dimensions Face Mount Back Mount Shank Dia. (mm) Face Mount Part Number Actual O.D. -0.01 -0.02 Clearance Drill Diameter E Bore +0.010 +0.003 F Depth +0.025 -0.025 G Tap Size & Depth1 H Bolt Circle Diameter 3 PL Equally Spaced Min. Subplate Thickness D Shank Dia. (mm) Back Mount Part Number Actual O.D. +0.04 +0.03 A Depth +0.025 -0.025 B C-Bore ±0.15 C Min. Subplate Thickness D 13 49556SS 35 13.5 35 11.91 M4x0.7 x 7 25 20 13 49566SS 20 6.92 26 20 16 49557SS 37 21.0 37 11.91 M4x0.7 x 7 29 20 16 49567SS 22 7.24 29 20 20 49551SS 45 21.0 45 16.21 M5x0.8 x 9 35 25 20 49561SS 28 8.74 33 25 25 49552SS 55 25.5 55 20.32 M6x1.0 x 10 42 30 25 49562SS 35 10.54 41 25 30 49553SS 60 30.5 60 22.15 M6x1.0 x 11 48 35 30 49563SS 42 10.95 49 30 35 49554SS 70 40.0 70 22.99 M8x1.25 x 17 56 40 35 49564SS 48 12.50 55 35 50 49555SS 92 55.0 92 31.50 M10x1.5 x 18 75 50 50 49565SS 67 15.75 76 45 QUICK CHANGE FIXTURING - ZERO POINT MOUNTING SYSTEM Jergens, Inc. | 15700 S. Waterloo Road | Cleveland, Ohio 44110-3898 USA W40-P1 BALL LOCK® MOUNTING SYSTEM workholding solutions QUICK CHANGE FIXTURING - BALL LOCK® MOUNTING SYSTEM 40 METRIC DIMENSIONS - METRIC FIXTURE/SUBPLATES
RkJQdWJsaXNoZXIy NzI2NjY=